5 Ways to Improve the Energy Efficiency of Your Home

Pipe Insulation5 Ways to Improve the Energy Efficiency of Your Home

It seems like every time we turn on the TV or open a newspaper we are being told about climate change and how it is up to us all to do our bit to help save the planet and reverse the effects of global warming. Coupled with this every time we open our gas and electricity bills they seem to be getting higher. Therefore many of us are deciding that it is time that we did our bit to make our homes more energy efficient and help to save the planet and lower our gas and electricity bills. There are many things which we can all do to improve the efficiency of our homes and below are some of our top tips.

· Install UPVC windows and UPVC doors, if you have older timber framed single glazed windows and doors they will be a weak spot in your home where heat will be lost. By installing UPVC windows and UPVC doors you will reduce the amount of heat lost considerably. As an added benefit UPVC windows and UPVC doors are also low maintenance and will not need to be painted every couple of years.

· Likewise conservatories are a weak spot in regards to heat loss. Again double glazed UPVC conservatories are more energy efficient than traditional wooden framed single glazed conservatories. By also adding internal doors between UPVC conservatories and the rest of the house allows you to shut the heat to the conservatory off when you are not using it.

· If you do not already have it then installing loft insulation is also highly recommended. Heat rises so it is only natural that the roof would be weak spot in the home. However by installing adequate loft insulation can reduce the amount of heat you lose through the roof space dramatically.

· Do you live in an older property? Then installing cavity wall insulation will reduce the amount of heat lost through the walls of your property considerably.

· Insulate your water tanks and pipes. By insulating your water tanks and pipes will keep your water hotter for longer as less heat is able to escape. A hot water jacket can be fitted to your water tank easily and will make a big difference.

If you are concerned about the energy efficiency of your home then now is the time to act. If nothing has been done to improve the efficiency of your home previously there are likely to be some simple changes you can make which will make a considerable difference.

Pipe Insulationpipe insulation tape

Understanding Insulation Ratings and Factors

Pipe InsulationUnderstanding Insulation Ratings and Factors

Terms of insulation can be very confusing for anyone outside the industry. If you have already purchased the insulation in the house, you know that the insulation with high R-factor is better. But what exactly does this mean? Did you know that the value of R depends on other factors?

When it comes to buying more specific insulation products, such as a removable insulating blanket for pipes, understanding the specificities of the three measures of isolation is the key.

The K factor
In order tounderstand the well-known R factor, it is important to understand the factors upon which it relies. The textbook definition of the K factor is “The time rate of steady heat flow through a unit area of homogeneous material induced by a unit temperature gradient in a direction perpendicular to that unit area.” That’s a mouthful.

Simplified, the K factor is the measure of heat that passes through one square foot of material that is 1 inch thick in an hour. Usually, insulation materials have a K Factor of less than 1. The lower the K value, the better the insulation.

The C Factor

C Factor stands for Thermal Conductance Factor. It’s the quantity of heat, measured in Btus, that passes through a foot of insulation material. Mathematically, it’s the K-factor divided by the thickness of the insulation material. Just like the K Factor, the lower the C factor, the better the insulating properties of the material.

The R Factor

Anyone who purchased insulation for their home knows what the R-factor is. It’s the number on the outside of the ungainly roll of itchy stuff. However, unbeknownst to most, the R-factor is not constant. It is the Thermal Resistance factor of insulation. In layman’s terms, this refers to the effectiveness of the insulation at retarding the transfer of heat.

The R factor is a variable value that measures the ability of a material to block heat rather than radiate it. The variable is the C factor. Mathematically, the R factor can be determined by R=1/C. The higher the R factor, the better the insulation.

The R factor basically pulls together all the information of the other factors and makes it easy to judge the effectiveness of insulating material. Keep in mind that these factors are specific to the materials being measured. For instance, if you take two pieces of batting that are rated at R 11 and put them together, you won’t get R 22 coverage. Understanding the ins and outs of the factors that help describe how effective insulation material is will go a long way to helping make the buying process easier.

Pipe Insulationpipe insulation

Pipe insulation foam

Pipe InsulationPipe insulation foam

Pipe foam insulation has recently received and programmed pauses various tax incentives and credits, as has just published the mainstream media. President Barack Obama has made a priority of his economic stimulus through the promotion of environmental initiatives, and this element of the reconstruction of property and buildings (new) is an important part of their economic recovery plans.

The idea is to introduce tax breaks to those who plant and pipe insulationas a direct result, homes appreciate in value, more and more real bottleneck and central to the current housing crisis. The White House and the Senate, as the difference in the number of agreements of health care in these green initiatives, especially those relating to the insulation and energy saving strategies, approaches, calls the new building.

If you are a new generator or a licensed contractor and linked, it is your responsibility to review these new sustainability, energy conservation (andin some cases, the production of energy), and also called green initiatives and programs, which offer great value for the parts of your business, and serve as the cornerstone of a great service for their field sales.

Meters, such as New York, San Francisco, Los Angeles and Phoenix are all on this train, and it is time for contractors and builders in cash in the funds market-related housing and the economy. Insulation Association of Canada has also approvedthese programs and initiatives such as Energy Star ™ programs to save the house and the other owners of hundreds of millions of U.S. dollars of cash incentives and tax cuts every year.

You can refer to building codes in your city online to see if the project of insulating foam tube is best suited to these initiatives is called green. Newer technologies substances in this experimental production of energy area that covers the white pipe insulationusing different methods for pipes and ducts presumably in the building where the pipes were used for the sole and exclusive. This unique approach to save a property of a few tens of U.S. dollars per year per square meter.

Also, if you need to strengthen their competitive advantage, be well informed about the latest green initiatives is very convincing in the initial offers and sales pitches.

Be well informed about the latest energy efficiency in homes is the best way to achievehidden value in your property. Millions of people in the United States should be sitting on a goldmine of sustainable and renewable sources of energy flows, like a water bed that can produce an infinite number of kilowatt turbines use of a strategic position Micro-called wind farms, solar parks small size. In the past it was common to find families that chickens and other peoples life uncomfortable for private consumption, and soon to be common to findfamilies grow its renewable energy and sustainable renewable natural place for private consumption.

Pipe Insulationpipe insulation tape

Basement Renovation

Pipe InsulationBasement Renovation

Renovation of the ground floor is a great way to free up space in your home. And unlike adding an addition on your house, the land / construction and installation of a new foundation are not required. Consequently, a project to renovate the basement can be much more convenient to do and offer a better return on investment.

But before you decide to start a basement renovation project, it is important first to develop a plan to renovate the basement.

Objectives of the basementProject

Part of a finished basement is a good list to fix the basement. For example, the basement is used for a playground or in the rooms? This is a bathroom or kitchen required? This is a cinema at home or in a part of the cave last year? Understanding how the basement will be used to help determine what mechanical engineering and the specific requirements needed for the current and proposed plans for restructuring in the basement.

DoTemporary repairs before the construction of the basement

The second important point that must be addressed prior to a renovation project on the ground floor to take care of all the problems that exist in the basement. For example, if there are cracks in the walls or floor must be repaired before starting the project to build the basement. In addition, leaks and sweating pipes, which must be repaired before remodeling. Also, if the construction plans of the base, includingHydraulic will require the demolition of the basement, it is essential to do so before the rest of the construction plan begins.

You should also consider the size and position of the oven. You must determine if the oven is hot enough for the existing basement, recently renovated? Otherwise, you may need a large oven. You should also consider the location of the furnace and the noise it generates. If the oven isnear a basement finished, then you may need to properly insulate the walls and outside the boiler room of the basement finished. You may also need to change the design of the furnaces so that fresh air is drawn out of the house.

Wall insulation should be considered. During the assessment phase / construction, rigid polystyrene insulation can be installed to make the basement warmer restored. Consider insulation requirements before startingrestructuring of the ground floor.

Basement Lighting

One of the most important aspects of a project to renovate the ground floor is the lighting. A finished basement is naturally dark is very attractive for family members and guests. To resolve this problem, its plans to renovate the basement should take into account the addition of natural light whenever possible. If the base has concrete walls on the knee, consider framing the windows in the walls above the knee. If the basement has an area, consider installingSliding glass doors or French.

In addition to adding natural light to the basement, consider installing ceiling lights and sconces can be in the walls. You can really light up the basement and make the space a warm and welcoming.

Basement One Last

During the development phase of the project cellar, consider sleeping and recreation areas near the daylight, for example, near regulators to strike.

If a home theater or wineWinery is part of the basement design objectives, areas located in the cellar, where the natural light is not necessary.

If space bathroom or kitchen design is part of the basement to locate targets just below the existing pipe on the first floor of the house. This will help reduce the amount of required pipe in the room with the beautiful head of a basement. It will also help limit the amount of structural work / checks required.

Again, if there is azone furnace to think in terms of noise, locate the warehouse or storage space near the furnace. These areas / rooms can help to isolate the rest of the underground environments, the noise from the boiler.

If Lally columns (support posts) that have to bear, trying to develop a plan to build underground walls acting as a Lally columns can be buried. If the burial is not possible, then consider systems with boxing orcomplete in order to become less of an obstacle and pain to the eyes, finished basement.

Basement Ceilings

When developing a project for the choice of the cellar ceiling is an important decision. Many homeowners decide to install suspended ceiling tiles, while others opt for the installation of the plaster ceiling. Both have their advantages and disadvantages. Dropped ceiling tiles allow easy access to pipes and cables, but the impact of dramatic high ceilings in chalkthe ceiling.

Plasterboard ceiling on the other hand can give a more finished and to provide more space, but access to the piping and wiring is limited. If the ceiling is plaster of your choice or by necessity due to limited ceiling height, a plan for the ports under the bathroom on the first floor J-traps, valves and electrical junction boxes key.

Who will do the remodeling of the floor of the building

Deciding to hire a contractor or do it yourself remodeling is always agood question. Yes, you can save money if you do it yourself. However, often many homeowners start a basement and never-ending project.

If you really want a finished basement, you have to be honest with yourself about the time commitment and expertise. If you can not spend your weekend in the 12/16 project, or lack of experience in the design and construction, then you should probably hire a general contractor, to be or to act as their own general contractor.

ARenovation project on the ground floor is a great way to provide space in your home for a fraction of the cost of building an addition on your house. With proper planning, a finished basement can become your home where family and friends want to spend all their free time. Good luck with your project to renovate the basement!

Pipe Insulationpipe insulation material

How not to install a central vacuum system

Pipe InsulationHow not to install a central vacuum system

I live in the house was built in 1953 and 60 in the central vacuum system is installed. In those days, was carried out for innovation, but many homeowners who have installed central vacuum systems in 50 and 60 have been disappointed with the product and returned with portable vacuums. Since then, the central vacuum industry has changed dramatically and today barely systems similar to those of the first day. The owners of the list today of a central vacuum systemas one of their favorite gadgets.

Over the past 30 years, the power units that are produced are incredibly more powerful than those of elementary units and accessories for cleaning have changed drastically. In addition, good practices for the installation have been established to contribute to the effectiveness of the systems. Central vacuum systems can be installed in almost all DIY in almost every home. If you decide to tackle this project, you'll be glad you didNo, but there are some pitfalls to be avoided if we consider the simple tips. Roger Ambrose, president of the Central Vacuum Stores says "follow the" how not "to make recommendations on the best central vacuum system."

1. Do not underestimate the power you need. The manufacturers provide a recommended sequence of units sold square, but, unfortunately, often underestimate the power you need. I never heard anyone complain about having too muchlarge amount of energy to get the most from your central vacuum system to increase its surface area of ​​at least 1.5 and buy a unit recommended for this number, instead of its actual size.

2. Do not install the power unit in a hot attic or a small confined space. Central vacuum motor must be in an area does not overheat.

3. Do not forget to hit all its accessories. Sometimes people get the tubeand accessories together, you can forget about being together. With use, the hose and accessories can be separated, if they do not stick. Make sure you put the glue on the pipe and then rotate the tube into the fitting.

4. 90 Do not use radios, except directly behind the entrance. Small radius of 90 are made for 2×4 walls. When you use something just behind the entrance is too large to pass through the system stops atand you can only reach y.

5. Do not put your joints back. Always use the accessories and install the scanner in the direction of airflow at the rear side of the engine. If you do this correctly, maximizing the efficiency of the central vacuum system.

If you install a central vacuum system, choose the "not as" highly recommend. You can also search centerEmpty business where technicians are ready to talk through before you begin the installation. In this way you know what it is before committing to a purchase.

Pipe Insulationwater pipe insulation